Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
We have noticed this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and believe it made sense to talk about it with you over here.
Mounting a tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult project. If the old bathtub is readily accessible, the task can move speedily; if you need to open up a wall to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the job as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to consider employing one before you start. Chances are you may require a professional plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your restroom if you have already purchased a brand-new bathtub and also don't require to transform the setup of your previous water system pipes.
Your devices and also material list ought to consist of the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Making use of both wood boards under its feet, put the bathtub in the called for placement. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the tub till the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water supply and check all joints and brand-new pipework for leakages and tighten them if necessary. Load the tub and additionally examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the tub should wait till the bathtub has been made use of a minimum of when as this will resolve it right into its last position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making sure that the washing machines are in area in between the faucet and also the sink. Protect the faucet in place with the producer given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The former type ought to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, causing issues with moisture and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can split rather very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that article on A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different website. Sharing is nice. Helping people is fun. Many thanks for going through it.
Quick solution? Call. Report this page